Empowering Indian businesses in the procurement ecosystem since 2012
| Tender ID | 2353721 |
|---|---|
| Organisation Name | Public Health Engineering Department |
| Tender Brief | Corrigendum : Supply, Installation, Testing And Commissioning Of Electro-mechanical Equipment At Water Supply Scheme Dachnimall (stage 1st And Stage 2nd) Of Jal Shakti (phe) Mechanical Division South Awantipora Under Jjm. |
| Last Date For Submission | 14th May, 2026 |
| Opening Date | 15 May, 2026 |
| Document Cost | 500.00 |
|---|---|
| EMD | 224821.00 |
| Estimated Cost | 7494038.00 |
| City | Awantipora |
|---|---|
| State | Jammu and Kashmir |
| # | Item | Qty | Units |
|---|---|---|---|
| 1 | WSS Dachnimall Stage 1st. | ||
| 2 | Supply, Installation, Testing & Commissioning of Submersible Pumping Unit V 6 as per IS 8034 with latest amendments having the specification as under:- PUMP: =Suitable for well casing Discharge = 2500 GPH assumed Head = 330 m Efficiency = Not less than 50% Speed = 2900 Rpm Type of pump : Mixed flow. Type of fluid to be handled = Ground water MATERIAL OF CONSTRUCTION: Impeller = Stainless Steel / Bronze/ chrome steel Pump Shaft = Stainless Steel SS 410. Pump Casing = Cast Iron/Stainless steel IMPELLER: Impeller is of the enclosed or semi enclosed type and properly balanced. Enclosed Impellers equipped with seal rings on their hubs. COUPLING: A suitable coupling arrangement provided with pump set. Non Return Valve: Non Return Valve of the suitable size provided above the pump discharge case. MOTOR:- Method of starting = Star Delta Speed = 2900 (Sync). Frequency = 50 3 % Hz Working Voltage = 380 -415 15% V, 03 phase Efficiency =As per IS 9283 (2013) with latest amendments. Rating = Not less than 25 HP Class of insulation = F/ B Submersible motor should be water filled, water lubricated squirrel cage type ,working on 3 phase; AC supply ranging from 380 to 415 volts, 50Hz. The motor should be sealed by radial rings to avoid mixing of well water with motor a) The job includes providing and fitting of interlocking arrangement against any failure of coupling. It must be fabricated out of MS strips of suitable size and length. b) The job includes providing and fitting of appropriate size MS nipple 2 feet long threaded on one end and welded to same size MS flange of thickness (as per Table-17) at other end for 65 mm diameter column pipe as per site requirement. The threaded portion should be as per size of pumping out let for proper fixing. The job includes providing and fitting of R. I. cloth joints/rubber washers with nuts, bolts and washers for all joints of column pipe. The job also includes lowering of pumping unit in the well then proper testing and commissioning of pumping unit on full load at site. Note: Providing of test certificate & Characteristic Curve of pumping equipment is compulsory. | 2.000 | Job |
| 3 | Supply, Installation, Testing & Commissioning of Submersible Pumping Unit V 6 as per IS 8034 with latest amendments having the specification as under:- PUMP: =Suitable for well casing Discharge = 2200 GPH assumed Head = 470 m Efficiency = Not less than 50% Speed = 2900 Rpm Type of pump : Mixed flow. Type of fluid to be handled = Ground water MATERIAL OF CONSTRUCTION: Impeller = Stainless Steel / Bronze/ chrome steel Pump Shaft = Stainless Steel SS 410. Pump Casing = Cast Iron/Stainless steel IMPELLER: Impeller is of the enclosed or semi enclosed type and properly balanced. Enclosed Impellers equipped with seal rings on their hubs. COUPLING: A suitable coupling arrangement provided with pump set. Non Return Valve: Non Return Valve of the suitable size provided above the pump discharge case. MOTOR:- Method of starting = Star Delta Speed = 2900 (Sync). Frequency = 50 3 % Hz Working Voltage = 380 -415 15% V, 03 phase Efficiency =As per IS 9283 (2013) with latest amendments. Rating = Not less than 30 HP Class of insulation = F/ B Submersible motor should be water filled, water lubricated squirrel cage type ,working on 3 phase; AC supply ranging from 380 to 415 volts, 50Hz. The motor should be sealed by radial rings to avoid mixing of well water with motor a) The job includes providing and fitting of interlocking arrangement against any failure of coupling. It must be fabricated out of MS strips of suitable size and length. b) The job includes providing and fitting of appropriate size MS nipple 2 feet long threaded on one end and welded to same size MS flange of thickness (as per Table-17) at other end for 65 mm diameter column pipe as per site requirement. The threaded portion should be as per size of pumping out let for proper fixing. The job includes providing and fitting of R. I. cloth joints/rubber washers with nuts, bolts and washers for all joints of column pipe. The job also includes lowering of pumping unit in the well then proper testing and commissioning of pumping unit on full load at site. Note: Providing of test certificate & Characteristic Curve of pumping equipment is compulsory. Suggested Make: CRI | 2.000 | Job |
| 4 | Fabrication, providing, fitting and lowering of C class column pipe conforming to IS: 1239 of length 10 Rft into the Production Well up to the desired depth; The job includes Providing and welding of flanges conforming to IS: 6392, Table-17 and PN 16 to these pipes and welding of flanges in two layers to make the flanged joint strong and leak proof. The pipe of 10 ft length is to be weld on both sides with flanges using welding rod of reputed make. The job includes all types of skilled labors, arrangement of power supply/ diesel Generator set etc required for the job including P/F of suitable size nuts bolts and R.I Gasket in the flanged joints of column pipes. The job further includes cutting of 2 No. rectangular cable slots in each flange. Any modification to the column pipes /flanges required during lowering is included in the job. Size : DN 50 Rating: PN 16 Class: C (Heavy) Test/inspection certificates from the Manufacturer must be produced on delivery of the item. | 20.000 | Job |
| 5 | Providing/supplying and fitting of G.I flanged Rising Main The Pipe shall be hot dip Galvanized, class C class Heavy pipe confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). The flanges shall be double welded both from inside and outside of the pipe using standard electrode of reputed make. Flanges (as per IS 6392/1997 Table:17) Thickness shall conform to IS 6392 Part 1st Table-17. The flange welding shall be carried out in double layers using reputed make electrodes to form strong welding joint. Welding Electrode DC Arc Welding using welding electrode having diameter not less than 4mm. Nuts and Bolts Nuts and Bolts (conforming to IS:1363 Part 1st) Rubber Insertion Gaskets Rubber Insertion Gaskets (conforming to IS: 638/79) to be used between flanged joints. The main technical specifications of the pipe are given here under: Size: DN 65mm Class "C" Heavy Note: Steep head load accounted for the execution of the job. Test/inspection certificates from the Manufacturer must be produced on delivery of the item. | 900.000 | Mtr |
12 Days Left