Empowering Indian businesses in the procurement ecosystem since 2012
| Tender ID | 4428127 |
|---|---|
| Organisation Name | Military Engineer Services |
| Tender Brief | Corrigendum : Repair To Flexible Rigid Surfaces Of Runway Including Application Of Pme Etc At Afs Jodhpur |
| Last Date For Submission | 29th Jun, 2026 |
| Opening Date | 01 Jul, 2026 |
| Document Cost | 1000.00 |
|---|---|
| EMD | 145000.00 |
| Estimated Cost | 7998000.00 |
| City | Jodhpur |
|---|---|
| State | Rajasthan |
| # | Item | Qty | Units |
|---|---|---|---|
| 1 | M&L for cleaning the surface by brushing with wire brushes for removing caked mud etc, sweeping with compressor air blower to remove all loose dust and dirt etc/taking out dust/ existing material with compressed air and making the surface free from dust, drying the surface and applying Two coats of polymeric modified emulsion (PME) by using self propelled emulsion distribution uniformly or towed emulsion pressure sprayer , equipped for spraying the PME uniformly and mopping the total undiluted PME @ 1.00 litre per sqm in two coats in ratio 1:1 (PME: water) and ensure uniform finish of total area complete all as specified and directed. Note: The tenderer shall take into consideration the following points while quoting rate for the above item:- (i) No price adjustment shall be applicable if excess quantity of polymer modified emulsion (PME) shall be used, depending upon condition of existing flexible surface. (ii) Special care shall be taken to fill gaps/cracks up to 6mm wide with 2.36 mm size coarse sand mixed with PME as per manufacturers instructons and quoted rate shall be included for same. | 26715.00 | Sqm |
| 2 | Material and Labour for Chipping and/or neatly Cutting of existing loose concrete at cracks on Runway/Taxi track/ pavement by using diamond cutter. Cutting of cracked portion shall not be less than 100 mm wide and 45 mm deep. Cleaning the dirt and all loose material fanned with air blower and air blasting the cleaned surface applying proprietary primer on surfaces to obtained tack and finally filling in Elastomeric Concrete, (Mix shall be prepared as per manufacturer) to obtained a true surface and finally tooling the set surface with hand tools complete all as specified and directed. Note :- (i) The rate shall be include for providing masking tape at joints and formwork required if any at spalled joints edges. (ii) The quoted rate deemed to be included for making good to disturbed joint filling around the area where material is applied. (iii) All material shall only be procured directly from manufacturer. | 16.00 | Sqm |
| 3 | Material and Labour Cutting existing loose patches / spalled edges of concrete pavement in square / rectangular/ triangular shape to a depth not less than 25mm removing debris out side MD land sweeping the patches with broom, cleaning with compressed air and applying epoxy resin mortar (proportion as specified) incl necessary form work for sides of joints, sprinkle , a thin layer of dust free fine sand (QUARTS SAND 10 No) and applying a coat on top of surface with epoxy resin primer @ 0.45 Kg/Sqm and finally filling the joints with sealing compound complete all as spd and as directed by Engr-in-Charge (Sealing of joint shall be measured under respective item separately). | 30.00 | Sqm |
| 4 | M&L for raking out sealing compound from existing expansion joints of dimension 25 mm to 30 mm wide and 45 mm deep, removing the debris from site by sweeping the concrete surface with brooms, cleaning with compressed air, treating sides and bottom of the joints with primer as per manufacturer's directions and filled with preformed closed cell polyethylene backup rod/strip of 25-32 mm dia, sealing with pitch free polyurethane grey sealant (minimum depth of sealant above backup rod shall be 10 mm) conforming to BS-5212 (Type FB) and applying masking tape on edges of joints to prevent accidental spillage of sealant and removing the masking tape after application of sealant complete all as specified and directed. | 600.00 | X RM |
| 5 | Ditto all as per item No 4 above but construction/dummy joints of dimension 16 to 24 mm wide and 40 mm deep and backup rod/strip of 16-25 mm complete all as specified and directed. | 1000.00 | X RM |
6 Days Left