| 1 | Supply / Fixing of Rectangular pole of height 6 mtr made out of MS pipe as per IS 4923. The pole shall be PU painted The pole shall have in built junction box weather proof flush door & locking arrangement for housing at bottom of the pole. Pole shall be made out of 200 mm x 100 mm Rectangular section of thickness 4 mm with base plate dimensions 325x225x16 mm thick. The base plate shall be machined & chamfered all four side by 6 mm ,25x25x3 mm ,angle jacket to be weld at two places all around with base plate , so pole to protect the base plate & pole weld joint. & also give the strength to the pole . The body of the decorative pole shall be painted properly to give it a smooth surface.The pole should have arragement for fixation of the mounting the fitting and the top of the pole should be openable for maintenance of fhe fitting . The decorative pole shall be duly pre-treated ( with phosphating ) & epoxy primer inside & outside of the part and painted in UV ray resistant PU coating in required colour. The coating should have a DFT of 80 micros Average. The pole shall be Powder coated. fhe fitting As per the Approval of E/ in charge. LED FIXTURE Supply/ Fixing of LED fixture in the aluminum special section box of size (Size 120 x 186 x 150 mm). Two no SQ LED module 4 LED's for outdoor applications Specific lighting system designed for street/pathway lighting, having Wattage of 35 W LED. Corrosion resistant extruded aluminum aesthetic housing Closed by a toughened optical grade safety glass diffuser and sealed with durable silicone rubber gaskets Easy installation, innovative Optimized Reflector mode from pure anodized aluminum, the reflector used inside has special coating for high reflectivity and long lifetime with maximum performance. Construction of LED module should be corrosion resistant die-cast aluminum housing designed to act as Heat Sink that can resist high temperature up to 55 degree Celsius and hard weather conditions, LED module should have special reflector optics thus providing excellent glare reduction and its special complex surface reflector technology with efficiency >80% LED module shall possess reflector based optics for smooth and full cut off light distribution with no light above 90 degrees CRI 80 Optimal performance with a glare-free, full cut-off, uniform lighting distribution. LED modale shall have optimized PCB design with touchdown technology. Optimal Performance with a glare -free full cut off, uniform lighting distribution. Excellent heat management operating temperature 5 C to 50 C Fixture should work well in operating temperature ranging from -30 C to +55 C, Ingress Protection IP66, Mechanical Impact resistance: IK08, Electrical Housing is polyester powder coated Corrosion resistant and superior quality finishes for all weather conditions. Mains Current AC 220V-240V 50/60Hz.Esyyshr 35W, Driving mA 700 mA, Driver Included, insulation class 1 4000K having lumen output of 4000 lumens. Dimensions 750mm(length) X 186mm(width) x 120mm(height) as per approved by the Engineer Incharge. | 1.00 | Nos |
| 2 | Supply / Fixing of Rectangular pole of height 4.5 mtr made out of MS pipe as per IS 4923. The pole shall be PU painted The pole shall have in built junction box weather proof flush door & locking arrangement for housing at bottom of the pole. Pole shall be made out of 200 mm x 100 mm Rectangular section of thickness 4 mm with base plate dimensions 325x225x16 mm thick. The base plate shall be machined & chamfered all four side by 6 mm ,25x25x3 mm ,angle jacket to be weld at two places all around with base plate , so pole to protect the base plate & pole weld joint. & also give the strength to the pole . The body of the decorative pole shall be painted properly to give it a smooth surface.The pole should have arragement for fixation of the mounting the fitting and the top of the pole should be openable for maintenance of fhe fitting . The decorative pole shall be duly pre-treated ( with phosphating ) & epoxy primer inside & outside of the part and painted in UV ray resistant PU coating in required colour. The coating should have a DFT of 80 micros Average. The pole shall be Powder coated. fhe fitting As per the Approval of E/ in charge. LED FIXTURE Supply/ Fixing of LED fixture in the aluminum special section box of size (Size 120 x 186 x 150 mm). One no SQ LED module 4 LED's for outdoor applications Specific lighting system designed for street/pathway lighting, having Wattage of 35 W LED. Corrosion resistant extruded aluminum aesthetic housing Closed by a toughened optical grade safety glass diffuser and sealed with durable silicone rubber gaskets Easy installation, innovative Optimized Reflector mode from pure anodized aluminum, the reflector used inside has special coating for high reflectivity and long lifetime with maximum performance. Construction of LED module should be corrosion resistant die-cast aluminum housing designed to act as Heat Sink that can resist high temperature up to 55 degree Celsius and hard weather conditions, LED module should have special reflector optics thus providing excellent glare reduction and its special complex surface reflector technology with efficiency >80% LED module shall possess reflector based optics for smooth and full cut off light distribution with no light above 90 degrees CRI 80 Optimal performance with a glare-free, full cut-off, uniform lighting distribution. LED modale shall have optimized PCB design with touchdown technology. Optimal Performance with a glare -free full cut off, uniform lighting distribution. Excellent heat management operating temperature 5 C to 50 C Fixture should work well in operating temperature ranging from -30 C to +55 C, Ingress Protection IP66, Mechanical Impact resistance: IK08, Electrical Housing is polyester powder coated Corrosion resistant and superior quality finishes for all weather conditions. Mains Current AC 220V-240V 50/60Hz.Esyyshr 35W, Driving mA 700 mA, Driver Included, insulation class 1 4000K having lumen output of 4000 lumens. Dimensions 750mm(length) X 186mm(width) x 120mm(height) as per approved by the Engineer Incharge. | 1.00 | Nos |
| 3 | Supply/ Fixing of LED fixture in the aluminum special section box of size (Size 120 x 186 x 150 mm). One no SQ LED module 4 LED's for outdoor applications Specific lighting system designed for street/pathway lighting, having Wattage of 35 W LED. Corrosion resistant extruded aluminum aesthetic housing Closed by a toughened optical grade safety glass diffuser and sealed with durable silicone rubber gaskets Easy installation, innovative Optimized Reflector mode from pure anodized aluminum, the reflector used inside has special coating for high reflectivity and long lifetime with maximum performance. Construction of LED module should be corrosion resistant die-cast aluminum housing designed to act as Heat Sink that can resist high temperature up to 55 degree Celsius and hard weather conditions, LED module should have special reflector optics thus providing excellent glare reduction and its special complex surface reflector technology with efficiency >80% LED module shall possess reflector based optics for smooth and full cut off light distribution with no light above 90 degrees CRI 80 Optimal performance with a glare-free, full cut-off, uniform lighting distribution. LED modale shall have optimized PCB design with touchdown technology. Optimal Performance with a glare -free full cut off, uniform lighting distribution. Excellent heat management operating temperature 5 C to 50 C Fixture should work well in operating temperature ranging from -30 C to +55 C, Ingress Protection IP66, Mechanical Impact resistance: IK08, Electrical Housing is polyester powder coated Corrosion resistant and superior quality finishes for all weather conditions. Mains Current AC 220V-240V 50/60Hz.Esyyshr 35W, Driving mA 700 mA, Driver Included, insulation class 1 4000K having lumen output of 4000 lumens. Dimensions 750mm(length) X 186mm(width) x 120mm(height) as per approved by the Engineer Incharge. | 25.00 | Nos. |
| 4 | Supply / Fixing of SITC of 12 Watt or more LED Bollard for outdoor applications Aesthetic appearance, Corrosion resistant aluminum housing, UV stabilized optical grade acrylic diffusers, Excellent heat dissipation to extend integral component life, Sealed with durable silicone rubber paskets, Easy installation, easy maintenance, Operating temperature 0 C to 50 C, Mechanical Impact resistance: IK08, Electrical Insulation: CLASS I, Housing is polyester powder coated Corrosion resistant and superior quality, finishes for all weather conditions, Colors: HMI to HM6 standard RAL (Optional), Ingress Protection. IP65, Aluminum Frame dimension: 200 x 200 mm and 1000 mm Height, with base plate 350 x 350 x 10 mm thick with 4 holes 18 mm dia for 16 mm dia foundation bolt as per attached drawing/design as per approved by the Engineer Incharge | 184.00 | Nos |
| 5 | SITC of concrete embedded Railing LED Light in ground up lighter adjustable IP 67/IK08 as per EN 6059% standards with 3W Led class I protection & CE certified how ng made up of fiberglass nylon with SS AISI 316L frame diffused made up of tempered glass resistant to impact & thermal shock reflector with symmetric profile driver inbuil as per approved by Engineer Incharge. | 290.00 | Nos |
