Empowering Indian businesses in the procurement ecosystem since 2012
| Tender ID | 3664107 |
|---|---|
| Organisation Name | District Administration |
| Tender Brief | Corrigendum : Supply And Installation Of Compact And Modular Solutions For Newly Constructed Office Building Of The Dm And Collector, North Tripura District. |
| Last Date For Submission | 30th Mar, 2026 |
| Opening Date | 02 Apr, 2026 |
| Document Cost | 4000.00 |
|---|---|
| EMD | 185798.00 |
| Estimated Cost | 9289860.00 |
| City | North Tripura |
|---|---|
| State | Tripura |
| # | Item | Qty | Units |
|---|---|---|---|
| 1 | Centre Table, size: 1000 (W) x 600 (D) x 450 (H) mm.----Overall Size : W x D x H - 1202 x 594 x 411mm 1. Body: All panels are made of 18mm Prelaminated Particle Board, with all exposed edges having 2mm thick PVC edge banding. Middle horizontal panel provides storage area. Four nylon bushes are provided. 2. Top: It has top surfaces made of glass & PLT panel. 8mm thick toughened glass with UV plate glued on it. This glass is fixed with the side vertical panels. PLT top panel is hinged with side vertical panels to open upwards. 3. Construction: Knock-down. 4. Finish: PLT panels are in WENGE shade having SUEDE finish. UV guled plates under glass have SUNRAY finish.5. Hardware: Dowels for knockdown assembly with high quality standard hardware like screw, door hinges, bumpers, expanding sockets, nylon bushes etc. | 2 | Sqft |
| 2 | 3 Seater Steel Lounge Chair----The seat shell is a welded assembly of seat,back and side frame.The seat and back are made of 0.12 0.013 cm thk CR steel sheet with oblong perforations.They are welded to sideframe of size 3.2 0.05 cm x 0.5 0.05 cm thk HR steel.The welded assembly is powder coated.The seat has a front water fall edge to provide popliteal clearance for comfortable seating.It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back.Clean and flat surfaces of seat and back aids in easy maintenance.Sear size:47.8 cm (W) x 44.6 cm (D).Back size:41.6 cm (W) x 23.0 cm (H).Understructure assembly consists of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5 0.03 cm x 0.2 0.016 cm thk.The welded structure assembly is powder coated.The leg assembly is fitted with shoes and levellers in nylon.The leg structure is designed with minimal area of contact close to ground providing easy access for cleaning purposes.The shoes fitted to leg assembly help in aligning the structure for back to back arrangements.Levellers take care of uneven flooring.Connecting beam is fitted with snap locking end cap.It also aids in side-by-side understructure alignment.Armrest assembly consists of armrest frame and armrest pad.The armrest frame is made up of size 3.175 0.05 cm x 0.47 0.027 cm thk HR steel and it is powder coated.Armrest pad is injection molded in nylon and is fitted onto the armrest frame. | 5 | Sqft |
| 3 | 3 Seater sofa----3 seater - Overall Size :Width :171cm Depth : 82cm Height :85cm Seating Height : 44cm Upholstery Material : PVC Shade : Burgundy Thickness : 1 mm Weight (GSM) : 575 Frame : Material : Pine Wood Moisture content : 10 12 % Foam : Material : Slab stock Density : Seat 32 kg/m3 and 28 kg/m3 with recron filler Back 28 kg/m3 Webbing : Material : Nylon Thickness : 2 mm Legs : Material : PVC with 70 mm bush | 2 | Sqft |
| 4 | Revolving Chair----The cushioned seat assembly consists of seat base moulded in glass-filled poly-amide,moulded polyurethane foam & upholstered with high stretch knitted polyester fabric.The cushioned back assembly consists of back inner moulded in polypropylene in - situ moulded with polyurethane foam & upholstered with high stretch knitted polyester fabric.Back size:45.5 cm (W) x 53.0 cm (H).Seat size:48.5 cm. (W) x 47.0 cm (D).The HR polyurethane foam used in seat and back cushion is moulded in density 45 2 kg/m ,and hardness load 16 2 kgf as per IS:7888 for 25% compression.The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back,without need for complex manual adjustments.The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes.The "S"shaped spines moulded in high strength glass-filled poly-amide and the spine connector moulded in glass-filled poly-amide form the back-spine structure involved in multi-dimensional recline motion.The variable tilt angle recline motion can be adjusted with 3 position tilt limit feature which is inbuilt in seat base and the tension is user weight dependent.The assembly is having fixed arm rest structure moulded in glass-filled poly-amide.The armrest top is made up of integral skin PU moulded over plastic inner moulded in glass-filled poly-amide.The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 0.3 cm.The pedestal is injection moulded in glass-filled poly-amide and fitted with 5 nos.twin wheel castors.The pedestal is 66.0 0.5 cm.pitch centre diameter and 76.0 1.0 cm.with castors.5 nos. twin wheel castors are injection moulded in poly-amide having 5.0 0.1 cm wheel diameter and assembled to the pedestal. | 56 | Sqft |
| 5 | 12 bodies Movable Storage System, Size: 2400 (W) x 3200 (D) x 1980 (H) mm.----Optimizer Plus Storage System is an efficient space saving arrangement catering to a variety of office storage requirements. Each of above configurations can have following type of blocks : i) Static Drive (SD), ii) Last Drive (LD), iii) Twin Drive (TD). Rigid Knock Down construction made of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Each body block consists. Each unit has 5 loading levels formed by 6 loading levels with 5 nos. adjustable shelves for 2361 mm. Height body.Body units are mounted on an understructure which is fixed or moving. Front Cover: It is the foremost panel of the body on which the handles Drive unit (Drive Type) are fixed. It is made of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Back Cover: It is the backmost panel of the body and is the mirror image of the front cover. It is made of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Back Panel: The back panels are made of 0.6 thk. CRCA Steel conforming to IS: 513 Gr.D. There are two back panels Top back panel and Bottom back panel. The two back panels are fixed together using machine screws. The purpose of the back panel is to act as a divider between 2 opposite shelves in twin body. Shared Panel: The shared panel acts as a partition between two adjacent bodies. It is made of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Tie rod assembly: The tie rod assembly acts as a substitute to the back panels (only in twin body). Optimizer Height for ground for 2361H body is 2502.5mm (2361 body + 80 understructure + 61.5 channel system). Finish: The bodies including shelves are given antirust surface treatment & are coated with epoxy polyester powder. The testing of paint is done for various physical & chemical properties as per IS: 101. The material is then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Storage capacity per shelf: The shelf is 1180mm in length and can hold up to 13 nos. of box files of size 85mm x 345mm x 285mm (Approx 100 kg/UDL. Understructure: The Understructure is a welded frame suitably fabricated to bear the loads based on configuration. All the components are made of HR sheet 3 mm thk. conforming to IS:2062. The understructure, after pre-treatment, is coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 40 microns. The handwheel is connected to the rollers through a Sprocket-Chain arrangement mounted on the side of the body. The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The sprocket-chain arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. Centralized Locking: Each Drive type unit has a Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. A centralized locking arrangement is also provided on drive unit cover. A cam lock and lever arrangement is fitted on the drive unit cover of the last movable body, i.e. (LD). | 1 | Cum |
5 Days Left