Empowering Indian businesses in the procurement ecosystem since 2012
| Tender ID | 4093757 |
|---|---|
| Organisation Name | Military Engineer Services |
| Tender Brief | Corrigendum : 85971 Spl Repair/replacement Against Ber Diesel Generator Set And Allied Works At Sub Station No. 2, 3 And 4 At Aicts Under Ge (south) Pune |
| Last Date For Submission | 15th May, 2026 |
| Opening Date | 22 May, 2026 |
| Document Cost | 1000.00 |
|---|---|
| EMD | 178000.00 |
| Estimated Cost | 10348000.00 |
| City | Pune |
|---|---|
| State | Maharashtra |
| # | Item | Qty | Units |
|---|---|---|---|
| 1 | Removing / Dismantling the existing DG Sets alongwith alternator complete including Diesel tank, panel boards, cables, silencer pipe etc and transporting the entire plant machineries to MES store yard approx 3 Km complete. The existing DG Sets, panel board and plinth / foundations shall be totally demolished to ground level and the debris shall be removed to a distance of 500 mtrs and to make good the disturbed floor to match with the existing floor finish complete all as specified and as directed. | 4.00 | EACH JOB |
| 2 | Supply, installing, testing and commissioning, factory assembled silent Diesel Engine driven Generator set conforming ISO-8528, fully wired alternator AC, to give an out put of 180 kVA continuously rating at a power factor 0.8 lagging, 3 phase 4 wire, 415 volts 50 Hz 1% supply, 1500 RPM, CPCB IV+ regulation, directly coupled with diesel engine liquid cooled mounted on common base frame complete with floor mounting fuel tank (Min 3mm thickness) & accessories, vibration damper pads, Standard Control Panel With Controller DSE 6120 MK III, Engine Safeties & Protections Battery With Leads, as per OEM etcincluding Exhaust gas piping of 125 mm dia MS black Class-B pipe welded including all necessary fitting reducer, flange, bend etc support & clamps with 50X50X3 mm equal angle and anti vibration mounting insulation of exhaust system with 50 mm thick mineral wool coverd with wire mesh and aluminium cladding (from DG set to out side of the building and comprising of following :- | 3.00 | EACH JOB |
| 3 | Ser. Item No. 2.00 Contd.... (A) Diesel Engine : Liquid cooled turbo charged with after cooler to deliver suitable BHP at 1500 RPM under NTP conditions of BS 5514 and conforming to ISO 3046, with an overload capacity of 10% for one hour in any 12 hours continuous operation with the following accessories, Diesel engine of rated speed at full load electric start developing with system with radiator and including electronic governor control of class G-3, engine control panel, lub oil pump, water pump, fuel tank, exhaust pipe with silencer and suitable for electric start with batteries of adequate capacity and suitable for alternator of specified capacity complete with fly wheel direct/ flexible coupling and coupling guard complete. (a) Radiator with blower fan or heat exchanger with guard. (b) Pipe coupling for engine cooling system piping. (c) Corrosion inhibitor coolant | ||
| 4 | Ser. Item No. 2.00 Contd.... (d) Paper element filters (i) Fuel filter (ii) Lube oil filter (iii) By pass (e) Fly wheel housing and fly wheel to suit alternator. (f) Engine bearing mechanism in fly wheel housing. (g) Shut off coil with safety for LLOP/HWT/over speed. (h) Dry type air cleaners and vacuum indicators. (j) Residential silencers. (k) Stainless steel exhaust flexible bellows. (l) BLANK (m) Battery charging alternator. | ||
| 5 | Ser. Item No. 2.00 Contd.... (o) Electronic instrument panel, complete with all accessories as per manufacturer's specifications displaying the following:- (i) Battery as per OEM specified (ii) Water temperature. (iii) Lubricating oil pressure. (iv) Engine speed -1500 Rpm (v) Engine hours (vi) Frequency. (vii) Voltage. (p) Safety control (Trip and indication). (i) High water temperature (ii) Low lube oil temperature (iii) Overspeed stop |
6 Days Left